MAX-11 Upper Receiver and Accessories

Note: All prices are subject to change without notice.

MAX-11 Slow Fire Upper Receiver$759.00 Image
This drop-in upper receiver converts your M-11/9 into a match winning subgun. Features include adjustable front and rear sights, full length M1913 scope rail and hard mount points for additional M1913 rails on right, left and bottom of front handgrip. Bottom rail included. Contained within the upper receiver is a heavy weight bolt assembly that telescopes over the barrel. The bolt weight is securely attached to the bolt assembly with two hardened cap screws- no welds to crack or break. This reduces the rate of fire (ROF) from 1,100 RPM down to around 600 RPM. Easily shoot single, double or triple round bursts- just count them off while its firing, it's that slow and easy. Due to the reduced ROF, muzzle rise is reduced and multiple rounds stay on target. The MAX-11 SF attaches to the stock M-11/9 lower receiver without any modification to the lower receiver.

The picture on the left shows a MAX-11 with additional Lage Mfg. accessories that are not included with the MAX-11 upper receiver. Accessories are available below. Registered lower receiver and magazine is not included.

Features:

1) Rear Sight , Adjustable 2) Front Sight , Adjustable 3) Scope/Optics rail (Mil-Std-1913) 4) Front Hand Grip 5) Front Grip Retaining Pin 6) Lower Accessory Rail (Mil-Std-1913) 7) 8" inch barrel length, removeable (threaded 1/2-28) 8) Flash Suppressor 9) Side Accessory Rail Mounting Points 10) Cocking Handle (reciprocating)
Image

Price is $759.00 each plus $21.00 for shipping within the CONUS (USPS Priority 2nd Day Delivery, with delivery confirmation).

Click here to see more pictures! Click here for MAX-11 Slowfire Upper Receiver- Owners Manual

Click here for ordering instructions.


MAX-11 Slow Fire Upper Receiver, Flat Top Version $759.00 Image
This Slow Fire Upper Receiver is the same as the MAX-11 above, except with a full length M1913 Picatinny rail on the top. Designed for use with removeable AR-15/M-16 sights (not included), or can be used with just a scope installed. When used with a C-More or Aimpoint red dot scope, Flip Up Iron sights will co-witness with the red dot.

The picture on the left shows a Flat Top MAX-11 with additional Lage Mfg. accessories that are not included with the MAX-11 upper receiver. Accessories are available below. Registered lower receiver and magazine is not included.

Click here to see more pictures! Click here for ordering instructions.

MAX-11,8" Replacement Barrel $86.00 Image
8 inch replacement barrel for the MAX-11. Available with muzzle threaded 1/2-28, 1/2-32 or 1/2-36. Click here for more information.






MAX-11,8-1/4" Barrel, 3/4-10 Thread $106.00 Image
8-1/4 inch replacement barrel for the MAX-11. Threaded 3/4-10. Click here for more information.








MAX-11,8-1/2" Barrel, 3-lug $184.00 Image
8-1/2 inch replacement barrel for the MAX-11. 3-lug. Click here for more information.









MAX-11,10" Unthreaded Barrel - SOLD OUT $99.00 Image
10" unthreaded barrel for the MAX-11. Click here for more information.








MAX-11 Speed Bolt$165.00 Image
Designed for use with the MAX-11 Slowfire Upper Receiver, this "Speed Bolt" bolt assembly was designed for those who like the look of the MAX-11 but wanted a faster rate of fire. This bolt assembly utilizes an aluminum bolt weight to speed up the rate of fire to around 900 rounds per minute. This is a complete bolt assembly requiring you to only swap out the bolt assembly of your MAX-11 to increase your rate of fire from the standard 600 RPM to 900 RPM.





MAX-11 Tactical Bolt $195.00 Image
The Tactical Bolt changes the rate of fire of the MAX-11 to approximately 750 RPM. This more aggressive rate of fire can be useful in Subgun Matches. With practice, you can still get off single shots when required and have a fast burst available when you need it. Customer's have also perceived that the recoil seems smoother. This bolt assembly utilizes a lightened steel bolt weight to speed up the rate of fire. This is a complete bolt assembly requiring you to only swap out the bolt assembly of your MAX-11 to increase your rate of fire from the standard 600 RPM to 750 RPM.





K-Grip $75.00 Image
Designed for use with the MAX-11 Slowfire Upper Receiver, this K-Grip replaces the standard grip. The grip is forward canted allowing a natural shooting stance. Easy to install, just remove the retaining pin from the MAX-11, remove grip, slide on K-Grip and re-install retaining pin.






Metal Foregrip, High Mount $115.00 Image
Designed for use with the MAX-11 Slowfire Upper Receiver, this all metal foregrip replaces the standard MAX-11 grip. The front is aluminum and the rest is all steel. Finished in tough KG Gunkote to match the manganese phosphate finish of the MAX-11. Features an integral lower picatinny rail. This high mount version provides a higher mounting of a vertical grip to keep your hand closer to the barrel centerline. To add or remove an accessory from the the lower rail requires removal of the 4 mounting screws. The bottom picatinny rail fits flush with the bottom of the lower receiver.



Metal Foregrip, Low Mount $115.00 Image
Designed for use with the MAX-11 Slowfire Upper Receiver, this all metal foregrip replaces the standard MAX-11 grip. The front is aluminum and the rest is all steel. Finished in tough KG Gunkote to match the maganese phosphate finish of the MAX-11. Features an integral lower picatinny rail. This low mount version allows addition or removal of accessories from the the lower rail without removal of the 4 mounting screws. The bottom picatinny rail protrudes below the bottom of the lower receiver.




Metal Foregrip, K-Grip $115.00 Image
Designed for use with the MAX-11 Slowfire Upper Receiver, this all metal foregrip with polymer forward canted K-Grip replaces the standard MAX-11 grip. The front is aluminum and the rest is all steel except the K-Grip handle. Finished in tough KG Gunkote to match the maganese phosphate finish of the MAX-11. Features a forward canted K-Grip without a picatinny rail on the bottom.






Side Accessory Rails $49.99 Image
Left and right side accessory rails for attaching additional accessories to the sides of the MAX-11 Slow Fire Upper Receiver such as flashlights or lasers. Matches the bottom accessory rail provided with the stock front grip on the MAX-11 Slow Fire Upper Receiver. Provided with spacers to allow use of accessories that require a higher mount. All mounting hardware provided.





MAX-11 Extended Cocking Knob $24.99 Image
Extended cocking knob for use exclusively with the MAX-11 Slow Fire Upper Receiver. 1/2" longer than the stock cocking knob to allow use with scopes or mounting systems that may interfere with the standard cocking knob. Click here for more information.





MAX-11 Suppressor Gas Block $24.99 Image

If you plan to do alot of shooting with a sound suppressor (silencer) on your MAX-11, you will definitely want to buy one of these. The Suppressor Gas Block reduces the amount of gasses directed towards your face during shooting. For maximum gas reduction, also purchase the Internal Suppressor Gas Block below. Click here for more information.





MAX-11 Internal Suppressor Gas Block $20.00 Image
The Internal Suppressor Gas Block further reduces the amount of gasses directed towards your face during shooting. It is installed in the lower receiver and blocks gasses from traveling to the rear of the receiver.






Fixed Buttstock- High Mount $79.00 Image
This durable black polymer buttstock is designed for use with the aftermarket M-11/9 upper receivers with higher sights or optics. This buttstock features a sling mount on the top rear of the buttstock. Easily installs with one screw and a threaded block that drops inside the lower receiver. Measures 8-1/2" from rear of receiver to end of buttpad. Length from backstrap of grip to buttpad is 12-1/4". Also available in 1" shorter or 1" longer length. Weighs 9.7 Ounces. Click here for pictures






Left Folding Buttstock $209.00 Image
This durable black polymer buttstock is is designed for use with the aftermarket M-11/9 upper receivers with higher sights or optics. This left folding buttstock features a sling mount on the top rear of the buttstock. When folded, it will not interfere with operation of the subgun. Easily un-folds and solidly locks in place. Installs with one screw and a threaded block that drops inside the lower receiver. Measures 8-1/2" from rear of receiver to end of buttpad. Length from backstrap of grip to buttpad is 12-1/4". Also available in 1" shorter or 1" longer length. Weighs 14.7 Ounces. Click here for pictures






Collapsible Buttstock $99.00 Image
This collapsible stock is a drop-in replacement for the wire form stock that comes with the M-11/9. Sturdy construction will not fold up in use. Two extendable positions to allow for heavy clothing, tactical vest or smaller shooters. Click here for pictures





ACE Rifle Stock Adapter $79.00 Image

This stock adapter is designed for use with the MAX-11 Slowfire Upper Receiver or other receivers with higher sight lines or scopes attached. Allows use of buttstocks manufactured by ACE LTD. USA. Click here for more information and pictures





2-Piece Molded Grip $49.99 Image
This molded polymer grip features one finger groove, ribs on the front, stippling on the sides, is more rounded on the backstrap than the stock grip and extends lower. It also features a "mag funnel" on the bottom. Click here for more information and pictures





2-Piece Molded Grip with Thumb Activated Magazine Release $79.99 Image
This molded polymer grip has the same features as the 2-piece molded grip above, with the addition of a lever above the grip to activate the heel mounted magazine release. Click here for more information and pictures







Extended Safety $49.99 Image
This extended safety makes it quick and easy to positively engage and disengage your safety. Great for use in subgun competitions. Get on target quickly without fumbling with the safety. Will fit the M-11/9 or the Powder Springs M-10/45 or M-10/9. Click here for more information and pictures





Internal Safety Slide $29.99 Image
This internal safety slide replaces the cheap cast aluminum one that came with your M-11/9. It is designed to have more bearing surface and is made from steel with a black oxide finish. The picture to the left shows the original safety slide on the top and the new and improved Lage Mfg. steel safety slide on the bottom. The picture clearly shows how the original aluminum safety slide can become warped and battered.





Hardened Sear $49.99 Image
This M-11/9 Sear is case hardened to provide extra strength and durability. Original sears may have been improperly hardened during the rush to get as many M-11/9 machineguns manufactured and registered prior to May of 1986. If your M-11/9 ocasionally continues to fire after letting go of the trigger or "runs away", your sear may be worn. Check the tip of the sear that engages the sear notch in the bolt to make sure it is not rounded off. If it is, replace the sear. These sears are case hardened, refinished in black oxide and marked "LAGE".





Improved Extractor $12.00 Image
If you are experiencing extraction problems with your M-11/9, odds are you need to replace your extractor with this improved design. This new design, which is standard equipment on all MAX-11 Slowfire Upper Receivers, features a wider extraction groove and improved angle on the face of the extractor. Manufactured from case hardened steel and finished in black oxide, this extractor is built to last.





M-11/9 Buffer $5.00 Image
This replacement buffer for the M-11/9 is manufactured from 1/4" thick neoprene. It is precision cut to insure a perfect fit and reliable performance.







Zytel Magazine Feedlip Kits $5.00 Image
Steel feedlip inserts to repair your worn out Zytel magazines. Also can be used to convert a standard M-11/9 magazine to shoot .380 ACP. Click here for more information and pictures





Lage Manufacturing T-Shirts and Caps T-Shirt- $10.00/Cap- $8.00 Image
High quality T-shirt with Lage Manufacturing logo and MAX-11 graphic on the back. Caps feature the logo only. Click here for more information and pictures





Textured Grip Cover Discontinued Image
The grip cover is a textured, non-slip, hard rubber covering for the metal on the grip.  The texture is like a heavy stippling. It covers up the wear marks from your fingers, protects the metal and gives a better grip. Click here for more information and pictures







MAX-11/9 Upper Receiver Discontinued Image
The MAX-11/9 Upper Receiver. 10" barrel, side cocking, adjustable sights and front handgrip. Click here for more information and pictures









Note: All prices are subject to change without notice.