MAX-11A1 Upper Receiver and Accessories

MAX-11A1/380 Upper Receiver $795.00

For use with .380 ACP ammunition, this drop-in upper receiver converts your SWD M-11A1 into a much more useable subgun. Features include adjustable front and rear sights, full length M1913 scope rail and hard mount points for additional M1913 rails on right, left and bottom of front handgrip. Bottom rail included. Contained within the upper receiver is a heavy weight bolt assembly that telescopes over the barrel. The bolt weight is securely attached to the bolt assembly with two hardened cap screws- no welds to crack or break. This reduces the rate of fire (ROF) from 1,800 RPM down to around 600 RPM. Easily shoot single, double or triple round bursts- just count them off while its firing, it's that slow and easy. Due to the reduced ROF, muzzle rise is reduced and multiple rounds stay on target. The MAX-11A1 attaches to the stock M-11A1 lower receiver without any modification to the lower receiver.

The picture on the left shows a MAX-11A1 with additional Lage Mfg. accessories that are not included with the MAX-11A1 upper receiver. Accessories are available below. Registered lower receiver and magazine is not included.

Features:

1) Rear Sight , Adjustable 2) Front Sight , Adjustable 3) Scope/Optics rail (Mil-Std-1913) 4) Front Hand Grip 5) Front Grip Retaining Pin 6) Lower Accessory Rail (Mil-Std-1913) 7) 8" inch barrel length, removeable (threaded 1/2-28) 8) Flash Suppressor 9) Side Accessory Rail Mounting Points 10) Cocking Handle (reciprocating)



Price is $795.00 each plus $21.00 for shipping within the CONUS (USPS Priority 2nd Day Delivery, with delivery confirmation).

Click hear to see video of MAX-11A1/380 Firing (3.20 Meg)

Click here for ordering instructions.

MAX-11A1/380 Upper Receiver, Flat Top Version $795.00

This Upper Receiver is the same as the MAX-11A1 above, except with a full length M1913 Picatinny rail on the top. Designed for use with removeable AR-15/M-16 sights (not included), or can be used with just a scope installed. When used with a C-More or Aimpoint red dot scope, Flip Up Iron sights will co-witness with the red dot.

The picture on the left shows a Flat Top MAX-11A1 with additional Lage Mfg. accessories that are not included with the MAX-11A1 upper receiver. Accessories are available below. Registered lower receiver and magazine is not included.


Price is $795.00 each plus $21.00 for shipping within the CONUS (USPS Priority 2nd Day Delivery, with delivery confirmation).

Click here for ordering instructions.

MAX-11A1/9 Upper Receiver $795.00

This upper receiver is a 9mm version of the MAX-11A1 upper receiver descibed above. Uses inexpensive 9mm ammunition and reduces the rate of fire (ROF) from 1,800 RPM down to around 950 RPM. The MAX-11A1 attaches to the stock M-11A1 lower receiver without any modification to the lower receiver.

The picture on the left shows a MAX-11A1 with additional Lage Mfg. accessories that are not included with the MAX-11A1 upper receiver. Accessories are available below. Registered lower receiver and magazine is not included.




Price is $795.00 each plus $21.00 for shipping and insurance within the CONUS (USPS Priority 2nd Day Delivery, with delivery confirmation).

Click here for ordering instructions.

MAX-11A1/9 Upper Receiver, Flat Top Version $795.00

This Upper Receiver is the same as the MAX-11A1/9 above, except with a full length M1913 Picatinny rail on the top. Designed for use with removeable AR-15/M-16 sights (not included), or can be used with just a scope installed. When used with a C-More or Aimpoint red dot scope, Flip Up Iron sights will co-witness with the red dot.

The picture on the left shows a Flat Top MAX-11A1 with additional Lage Mfg. accessories that are not included with the MAX-11A1 upper receiver. Accessories are available below. Registered lower receiver and magazine is not included. <


Price is $795.00 each plus $21.00 for shipping and insurance within the CONUS (USPS Priority 2nd Day Delivery, with delivery confirmation).

Click hear to see video of MAX-11A1/9 Firing (2.40 Meg)

Click here for ordering instructions.

MAX-11A1, 8" Replacement Barrel $96.00

8 inch replacement barrel for the MAX-11A1. Muzzle threaded 1/2-28. Available in 9mm and .380 ACP. Barrel is engraved with bullet caliber.

MAX-11A1/9, 8-1/4" Barrel, 3/4-10 Thread $116.00

8-1/4 inch replacement barrel for the MAX-11A1/9. Threaded 3/4-10. Available in 9mm only and engraved "9mm" on the barrel.

MAX-11A1/9,8-1/2" Barrel, 3-lug $194.00

8-1/2 inch replacement barrel for the MAX-11A1/9. 3-lug. Available in 9mm only and engraved "9mm" on the barrel.

MAX-11A1/380 Replacement Bolt Assembly $205.00

Replacement bolt assembly for the MAX-11A1/380. ".380 ACP" is engraved on bolt.

MAX-11A1/9 Replacement Bolt Assembly $205.00

Replacement bolt assembly for the MAX-11A1/9. "9mm" is engraved on bolt.

K-Grip $75.00

Designed for use with the MAX-11A1 Slowfire Upper Receiver, this K-Grip replaces the standard grip. The grip is forward canted allowing a natural shooting stance. Easy to install, just remove the retaining pin from the MAX-11, remove grip, slide on K-Grip and re-install retaining pin.

Metal Foregrip, High Mount $115.00

Designed for use with the MAX-11A1 Slowfire Upper Receiver, this all metal foregrip replaces the standard MAX-11 grip. The front is aluminum and the rest is all steel. Finished in tough KG Gunkote to match the maganese phosphate finish of the MAX-11A1. Features an integral lower picatinny rail. This high mount version provides a higher mounting of a vertical grip to keep your hand closer to the barrel centerline. To add or remove an accessory from the the lower rail requires removal of the 4 mounting screws. The bottom picatinny rail fits flush with the bottom of the lower receiver.

Metal Foregrip, Low Mount $115.00

Designed for use with the MAX-11 Slowfire Upper Receiver, this all metal foregrip replaces the standard MAX-11A1A1 grip. The front is aluminum and the rest is all steel. Finished in tough KG Gunkote to match the maganese phosphate finish of the MAX-11A1. Features an integral lower picatinny rail. This low mount version allows addition or removal of accessories from the the lower rail without removal of the 4 mounting screws. The bottom picatinny rail protrudes below the bottom of the lower receiver.

Metal Foregrip, K-Grip $115.00

Designed for use with the MAX-11A1 Slowfire Upper Receiver, this all metal foregrip with polymer forward canted K-Grip replaces the standard MAX-11 grip. The front is aluminum and the rest is all steel except the K-Grip handle. Finished in tough KG Gunkote to match the maganese phosphate finish of the MAX-11A1. Features a forward canted K-Grip without a picatinny rail on the bottom.

Side Accessory Rails $49.99

Left and right side accessory rails for attaching additional accessories to the sides of the MAX-11A1 Slow Fire Upper Receiver such as flashlights or lasers. Matches the bottom accessory rail provided with the stock front grip on the MAX-11A1 Slow Fire Upper Receiver. Provided with spacers to allow use of accessories that require a higher mount. All mounting hardware provided.

MAX-11A1 Extended Cocking Knob $24.99

Extended cocking knob for use with the MAX-11A1 Slow Fire Upper Receiver. 1/2" longer than the stock cocking knob to allow use with scopes or mounting systems that may interfere with the standard cocking knob. Click here for more information.

MAX-11 Suppressor Gas Block $24.99

If you plan to do alot of shooting with a sound suppressor (silencer) on your MAX-11A1, you will definitely want to buy one of these. The Suppressor Gas Block reduces the amount of gasses directed towards your face during shooting. For maximum gas reduction, also purchase the Internal Suppressor Gas Block below. Click here for more information.

Fixed Buttstock- High Mount $129.98

This durable black polymer buttstock is is designed for use with the aftermarket M-11A1 upper receivers with higher sights or optics. This buttstock features a sling mount on the top rear of the buttstock. Easily installs with one screw and a threaded block that drops inside the lower receiver. Measures 8-7/8" from rear of receiver to end of buttpad. Length from backstrap of grip to buttpad is 11-1/8". Also available in 1" and 2" shorter length. Weighs 10.2 Ounces. Click here for pictures

Left Folding Buttstock $209.00

This durable black polymer buttstock is is designed for use with the aftermarket M-11/9 upper receivers with higher sights or optics. This left folding buttstock features a sling mount on the top rear of the buttstock. When folded, it will not interfere with operation of the subgun. Easily un-folds and solidly locks in place. Installs with one screw and a threaded block that drops inside the lower receiver. Measures 9-1/2" from rear of receiver to end of buttpad. Length from backstrap of grip to buttpad is 11-7/8". Weighs 13.2 Ounces. Click here for pictures

ACE Rifle Stock Adapter $79.00

This stock adapter is designed for use with the MAX-11A1 Slowfire Upper Receiver or other receivers with higher sight lines or scopes attached. Allows use of buttstocks manufactured by ACE LTD. USA. Click here for more information and pictures

2-Piece Molded Grip $49.99

This molded polymer grip features one finger groove, ribs on the front, stippling on the sides, is more rounded on the backstrap than the stock grip and extends lower. It also features a "mag funnel" on the bottom.

2-Piece Molded Grip with Thumb Activated Magazine Release $79.99

This molded polymer grip has the same features as the 2-piece molded grip above, with the addition of a lever above the grip to activate the heel mounted magazine release.

Extended Safety $49.99

This extended safety makes it quick and easy to positively engage and disengage your safety. Great for use in subgun competitions. Get on target quickly without fumbling with the safety. Will fit the M-11/9, M-11A1 .380 or the Powder Springs M-10/45 or M-10/9. Click here for more information and pictures

Internal Safety Slide $29.99

This internal safety slide replaces the cheap cast aluminum one that came with your M-11A1. It is designed to have more bearing surface and is made from steel with a black oxide finish. The picture to the left shows the original safety slide on the top and the new and improved Lage Mfg. steel safety slide on the bottom. The picture clearly shows how the original aluminum safety slide can become warped and battered.

Hardened Sear $49.99

This M-11A1 Sear is case hardened to provide extra strength and durability. Original sears may have been improperly hardened during the rush to get as many M-11/9 machineguns manufactured and registered prior to May of 1986. If your M-11A1 ocasionally continues to fire after letting go of the trigger or "runs away", your sear may be worn. Check the tip of the sear that engages the sear notch in the bolt to make sure it is not rounded off. If it is, replace the sear. These sears are case hardened, refinished in black oxide and marked "LAGE".

M-11A1 Buffer $5.00

This replacement buffer for the M-11A1 is manufactured from 1/4" thick neoprene. It is precision cut to insure a perfect fit and reliable performance.

Zytel Magazine Feedlip Kits $5.00

Steel feedlip inserts to repair your worn out Zytel magazines. Also can be used to convert a standard M-11/9 magazine to shoot .380 ACP.

Click here for more information and pictures